• [ CX24C512 ]

样品申请

目录

• 1.产品概述       2.产品特点     bDi嘉泰姆

• 3.应用范围       4.技术规格书下载（PDF文档）bDi嘉泰姆

• 5.产品封装       6.电路原理图  bDi嘉泰姆

• 7.相关产品bDi嘉泰姆

   产品概述 返回TOPbDi嘉泰姆

TheCX24C512 CX24C512G are EEPROM devices that use the industrial standard 2-wire interface for communications. The CX24C512 CX24C512G contains a memory array of 512K-bits (65,536x8), which is organized in 128-byte per page. The EEPROM can operate in a wide voltage range from 1.7V to 5.5V which fits most application. This product can provide a low-power 2-wire EEPROM solution. The device is offered in Lead-free, RoHS, halogen free or Green. The available package types are 8-pin SOIC/SOP, TSSOP, DFN and CSP. The CX24C512 CX24C512Gis compatible with the industrial standard 2-wire bus protocol. If in case the bus is not responded, a new sent Op-code command will reset the bus and the device will respond correctly. The simple bus consists of the Serial Clock wire (SCL) and the Serial Data wire (SDA). Utilizing such bus protocol, a Master device, such as a microcontroller, can usually control one or more Slave devices, alike this CX24C512G The bit stream over the SDA line includes a series of bytes, which identifies a particular Slave device, an instruction, an address within that Slave device, and a series of data, if appropriate. The CX24C512Galso has a Write Protect pin (WP) to allow blocking any write operations over specified memory area. Under no circumstance, the device will be hung up. In order to refrain the state machine entering into a wrong state during power-up sequence or a power toggle off-on condition, a power on reset circuit is embedded. During power-up, the device does not respond to any instructions until the supply voltage (VCC) has reached an acceptable stable level above the reset threshold voltage. Once VCC passes the power on reset threshold, the device is reset and enters into the Standby mode. This would also avoid any inadvertent Write operations during power-up stage. During power-down process, the device will enter into standby mode, once VCC drops below the power on reset threshold voltage. In addition, the device will be in standby mode after receiving the Stop command, provided that no internal write operation is in progress. Nevertheless, it is illegal to send a command unless the VCC is within its operating level.

   产品特点 返回TOPbDi嘉泰姆

 Two-Wire Serial Interface, I2C TM Compatible bDi嘉泰姆

– Bi-directional data transfer protocol bDi嘉泰姆

 Wide-voltage Operation – VCC = 1.7V to 5.5V bDi嘉泰姆

 Speed: 400 KHz (1.7V) and 1 MHz (2.5V~5.5V) bDi嘉泰姆

 Standby current (max.): 1A, 1.7V bDi嘉泰姆

 Operating current (max.): 2 mA, 1.7V bDi嘉泰姆

 Hardware Data Protection – Write Protect Pin bDi嘉泰姆

 Sequential & Random Read Features bDi嘉泰姆

 Memory organization: 65,536 x 8 bits bDi嘉泰姆

 Page Size: 128 bytes bDi嘉泰姆

 Page write mode bDi嘉泰姆

– Up to 128 bytes per page write bDi嘉泰姆

 Self timed write cycle with auto clear: 5ms (max.) bDi嘉泰姆

 Filtered inputs for noise suppression bDi嘉泰姆

 High-reliability bDi嘉泰姆

– Endurance: 1 million cycles bDi嘉泰姆

– Data retention: 100 years bDi嘉泰姆

 Industrial temperature grades bDi嘉泰姆

 Packages: SOIC/SOP, TSSOP, DFN and CSP bDi嘉泰姆

 Lead-free, RoHS, Halogen free, GreenbDi嘉泰姆

   应用范围 返回TOPbDi嘉泰姆

   abDi嘉泰姆

   技术规格书（产品PDF) 返回TOP bDi嘉泰姆

     需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！bDi嘉泰姆

 bDi嘉泰姆

产品封装图 返回TOPbDi嘉泰姆

bDi嘉泰姆

电路原理图 返回TOPbDi嘉泰姆

bDi嘉泰姆

相关芯片选择指南 返回TOP

◀ 上一篇:CX24C256提供262144位串行电可擦可编程只读存储器EEPROM每8位32768字存储敏感的应用程序参数I2C双向数据传输协议施密特触发器噪声抑制的滤波输入

返回顶部

下一篇▶:CX24C512G

共有条评论 用户名: 密码: 验证码: 匿名发表