目录EPi嘉泰姆

1.产品概述                       2.产品特点EPi嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 EPi嘉泰姆
5.产品封装图                     6.电路原理图                   EPi嘉泰姆
7.功能概述                        8.相关产品EPi嘉泰姆

一,产品概述(General Description)   EPi嘉泰姆

 CXSD62130 CXSD62130A is a 1.5MHz high efficiency monolithic synchronous buck regulator. Design with current mode scheme,the CXSD62130 CXSD62130A is stable EPi嘉泰姆

with ceramic output capacitor. Input voltage from 2.7V to 6.0V makes the EPi嘉泰姆

CXSD62130 CXSD62130A ideally suited for single Li-Ion battery powered EPi嘉泰姆

applications. 100%duty cycle provides low dropout operation, extending EPi嘉泰姆

battery life in portable electrical devices. Theinternally fixed 1.5MHz EPi嘉泰姆

operating frequency allows the using of small surface mount inductors and capacitors. The synchronous switches included inside increase the efficiencyEPi嘉泰姆

and eliminate the need of an external Schottky diode.EPi嘉泰姆
   The CXSD62130 CXSD62130A is available in TDFN2x2-6 packages.EPi嘉泰姆
二.产品特点(Features)EPi嘉泰姆

1A Output CurrentEPi嘉泰姆
Wide 2.7V~6.0V Input VoltageEPi嘉泰姆
Fixed 1.5MHz Switching FrequencyEPi嘉泰姆
Low Dropout Operating at 100% Duty CycleEPi嘉泰姆
25μA Quiescent CurrentEPi嘉泰姆
Synchronous RectifierEPi嘉泰姆
0.6V Reference VoltageEPi嘉泰姆
<0.5μA Input Current During ShutdownEPi嘉泰姆
Short-Circuit ProtectionEPi嘉泰姆
Over-Temperature ProtectionEPi嘉泰姆
Available in TDFN2x2-6 PackagesEPi嘉泰姆
Lead Free and Green Devices AvailableEPi嘉泰姆
(RoHS Compliant)EPi嘉泰姆
三,应用范围 (Applications)EPi嘉泰姆

HD STBEPi嘉泰姆
BT MouseEPi嘉泰姆
PND InstrumentEPi嘉泰姆
Portable InstrumentEPi嘉泰姆
四.下载产品资料PDF文档 EPi嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！EPi嘉泰姆

 EPi嘉泰姆

五,产品封装图 (Package)EPi嘉泰姆

EPi嘉泰姆
六.电路原理图EPi嘉泰姆

EPi嘉泰姆
EPi嘉泰姆

七,功能概述EPi嘉泰姆

Main Control LoopEPi嘉泰姆
The CXSD62130 CXSD62130A is a constant frequency, synchronous rectifier and current-mode EPi嘉泰姆

switching regulato r. In normal operation, the internal P-channel power MOSFET is turned on eachEPi嘉泰姆

 cycle. The peak inductor current at which ICMP turn off the P-FET is controlled by the voltage onEPi嘉泰姆

 the COMP node, which is the output of the error amplifier (EAMP). An external resistive divider EPi嘉泰姆

connected between VOUT and ground allows the EAMP to receive an output feedback voltage EPi嘉泰姆

VFB at FB pin. When the load current increases, it causes a slightly decrease in VFB relative toEPi嘉泰姆

the 0.6V reference, which in turn causes the COMP voltage to increase until the average EPi嘉泰姆

inductor current matches the new load current.EPi嘉泰姆
Enable/ShutdownEPi嘉泰姆
Driving RUN to the ground places the CXSD62130 CXSD62130A in shutdown mode. WhenEPi嘉泰姆

 in shutdown, the internal power MOSFETs turn off, all internal circuitry shuts down and theEPi嘉泰姆

 quiescent supply current reduces to 0.5μA maximum.EPi嘉泰姆
Pulse Frequency Modulation Mode (PFM)EPi嘉泰姆
The CXSD62130 CXSD62130A is a fixed frequency, peak current mode PWM step-down EPi嘉泰姆

converter. At light loads, the CXSD62130 CXSD62130A will automatically enter in pulse EPi嘉泰姆

frequency mode operation to reduce the dominant switching losses. In PFM operation, EPi嘉泰姆

the inductor current may reach zero or reverse on each pulse. A zero current comparator EPi嘉泰姆

turn off the N-FET, forcing DCM operation at light load. These controls get very low EPi嘉泰姆

quiescent current, help to maintain high effi-ciency over the complete load range.EPi嘉泰姆
Slope Compensation and Inductor Peak CurrentEPi嘉泰姆
The CXSD62130 CXSD62130A is a peak current mode PWM step downconverter. ToEPi嘉泰姆

 prevent sub-harmonic oscillations, theCXSD62130 CXSD62130A sense the peak current and EPi嘉泰姆

add slope compensation to stable the converter. It is accomplished in-ternally by addingEPi嘉泰姆

a compensating ramp to the inductor current signal at duty cycles in excess of 40%.EPi嘉泰姆

 Normally,this results in a reduction of maximum inductor peak current for duty cycles >EPi嘉泰姆

 40%. However, the CXSD62130 CXSD62130A uses a special scheme that counteracts this EPi嘉泰姆

compensating ramp, which allows the maximum inductor peak current to remain unaffectedEPi嘉泰姆

 throughout all duty cycles.EPi嘉泰姆
Dropout OperationEPi嘉泰姆
As the input supply voltage decreases to a value ap-proaching the output voltage, the dutyEPi嘉泰姆

 cycle increases toward the maximum on time. Further, reduction of thesupply voltage forces EPi嘉泰姆

the main switch to remain on for more than one cycle until it reaches 100% duty cycle. TheEPi嘉泰姆

 input voltage minus the voltage drop will determine the output voltage across the P-FETEPi嘉泰姆

 and the inductor.An important detail to remember is that on resistance of P-FET switch EPi嘉泰姆

will increase at low input supply voltageTherefore, the user should calculate the power dissipa-EPi嘉泰姆
tion when the CXSD62130 CXSD62130A is used at 100% duty cycle with low input voltage.EPi嘉泰姆
Over-Temperature Protection (OTP)EPi嘉泰姆
The over-temperature circuit limits the junction tempera-ture of the CXSD62130 CXSD62130A. EPi嘉泰姆

When the junction temperature ex-ceeds 150oC, a thermal sensor turns off the both power EPi嘉泰姆

MOSFETs, allowing the devices to cool. The thermal sen-sor allows the converters to start a EPi嘉泰姆

soft-start process and regulate the output voltage again after the junction tem-perature coolsEPi嘉泰姆

 by 30oC. The OTP is designed with a 30oC hysteresis to lower the average JunctionEPi嘉泰姆

 Temperature (TJ) during continuous thermal overload conditions, in-creasing the lifetime EPi嘉泰姆

of the device.EPi嘉泰姆
八,相关产品                    更多同类产品.......EPi嘉泰姆

共有条评论 用户名: 密码: 验证码: 匿名发表