目录tTr嘉泰姆

1.产品概述                       2.产品特点tTr嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 tTr嘉泰姆
5.产品封装图                     6.电路原理图                   tTr嘉泰姆
7.功能概述                        8.相关产品tTr嘉泰姆

一,产品概述(General Description)         tTr嘉泰姆

    The CXSD61055 is a fully integrated, high– efficiency 2A synchronous rectified step-down converter.The CXSD61055 operates at high efficiency over a wide output current load range.tTr嘉泰姆
This device offers two operation modes, PWM control and PFM Mode switching control, which allows a high efficiency over the wider range of the load.tTr嘉泰姆
    The CXSD61055 requires a minimum number of readily available standard externaltTr嘉泰姆
components and is available in an 6-pin SOT23 ROHS compliant package.tTr嘉泰姆
二.产品特点(Features)tTr嘉泰姆

1.)High Efficiency: Up to 96%tTr嘉泰姆
2.)600KHz Frequency OperationtTr嘉泰姆
3.)2A Output CurrenttTr嘉泰姆
4.)No Schottky Diode RequiredtTr嘉泰姆
5.)4.5V to 16V Input Voltage RangetTr嘉泰姆
6.)0.6V ReferencetTr嘉泰姆
7.)Slope Compensated Current Mode Control fortTr嘉泰姆
     Excellent Line and Load Transient ResponsetTr嘉泰姆
8.)Integrated internal compensationtTr嘉泰姆
9.)Stable with Low ESR Ceramic Output CapacitorstTr嘉泰姆
10.)Over Current Protection with Hiccup-ModetTr嘉泰姆
11.)Thermal ShutdowntTr嘉泰姆
12.)Inrush Current Limit and Soft StarttTr嘉泰姆
13.)Available in SOT23-6 PackagetTr嘉泰姆
14.)-40°C to +85°C Temperature RangetTr嘉泰姆
三,应用范围 (Applications)tTr嘉泰姆

Distributed Power SystemstTr嘉泰姆
Digital Set Top BoxestTr嘉泰姆
Flat Panel Television and MonitorstTr嘉泰姆
Wireless and DSL ModemstTr嘉泰姆
Notebook ComputertTr嘉泰姆
四.下载产品资料PDF文档 tTr嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！tTr嘉泰姆

 tTr嘉泰姆

五,产品封装图 (Package)tTr嘉泰姆
tTr嘉泰姆

六.电路原理图tTr嘉泰姆
tTr嘉泰姆
七,功能概述tTr嘉泰姆

Internal RegulatortTr嘉泰姆
    The CXSD61055 is a current mode step down DC/DC converter that provides excellent transienttTr嘉泰姆
response with no extra external compensation components. This device contains an internal,tTr嘉泰姆
low resistance, high voltage power MOSFET, and operates at a high 600K operating frequency totTr嘉泰姆
ensure a compact, high efficiency design with excellent AC and DC performance. tTr嘉泰姆
Error AmplifiertTr嘉泰姆
The error amplifier compares the FB pin voltage with the internal FB reference (V FB) and outputs atTr嘉泰姆
current proportional to the difference between the two. This output current is then used to chargetTr嘉泰姆
or discharge the internal compensation network to form the COMP voltage, which is used totTr嘉泰姆
control the power MOSFET current.The optimized internal compensation network minimizes thetTr嘉泰姆
external component counts and simplifies the control loop design. tTr嘉泰姆
Internal Soft-StarttTr嘉泰姆
The soft-start is implemented to prevent the converter output voltage from overshootingtTr嘉泰姆
during startup. When the chip starts, the internal circuitry generates a soft-start voltage (SS)tTr嘉泰姆
ramping up from 0V to 0.6V. When it is lower than the internal reference (REF), SS overridestTr嘉泰姆
REF so the error amplifier uses SS as the reference. When SS is higher than REF, REFtTr嘉泰姆
regains control. The SS time is internally fixed to 1 ms. Over-Current-Protection and HiccuptTr嘉泰姆
The CXSD61055 has cycle-by-cycle over current limit when the inductor current peak valuetTr嘉泰姆
exceeds the set current limit threshold. Meanwhile, output voltage starts to drop until FBtTr嘉泰姆
is below the Under-Voltage (UV) threshold,typically 30% below the reference. Once a UV istTr嘉泰姆
triggered, the CXSD61055 enters hiccup mode to periodically restart the part. This protection modetTr嘉泰姆
is especially useful when the output is dead-short to ground. The average short circuittTr嘉泰姆
current is greatly reduced to alleviate the thermal issue and to protect the regulator. The CXSD61055tTr嘉泰姆
exits the hiccup mode once the over current condition is removed. tTr嘉泰姆
Startup and ShutdowntTr嘉泰姆
If both VIN and EN are higher than their appropriate thresholds, the chip starts. ThetTr嘉泰姆
reference block starts first, generating stable reference voltage and currents, and then thetTr嘉泰姆
internal regulator is enabled. The regulator provides stable supply for the remainingtTr嘉泰姆
circuitries. Three events can shut down the chip: EN low, VIN low and thermal shutdown. In thetTr嘉泰姆
shutdown procedure, the signaling path is first blocked to avoid any fault triggering. The COMPtTr嘉泰姆
voltage and the internal supply rail are then pulled down. The floating driver is not subject totTr嘉泰姆
this shutdown command.tTr嘉泰姆
八,相关产品                     更多同类产品......tTr嘉泰姆

共有条评论 用户名: 密码: 验证码: 匿名发表