• [ 产品资料下载 ]

样品申请

目录AhA嘉泰姆

1.产品概述                       2.产品特点AhA嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 AhA嘉泰姆
5.产品封装图                     6.电路原理图                   AhA嘉泰姆
7.功能概述                        8.相关产品AhA嘉泰姆

一,产品概述(General Description)    AhA嘉泰姆

      The CXSD6293 is a single-phase, constant-on-time, and  synchronousAhA嘉泰姆
PWM controller, which drives N-channel MOSFETs. An internal 0.5V temperature-compensated reference voltage with high accuracy is designed to meet theAhA嘉泰姆
requirement of low output voltage applications. The CXSD6293 steps downAhA嘉泰姆
high voltage to generate low-volt-age chipset or RAM supplies in notebookAhA嘉泰姆
computers.The PWM controller operates fixed 300kHz pseudo-con-AhA嘉泰姆
stant frequency PWM with an adaptive constant-on-time control. The deviceAhA嘉泰姆
provides excellent transient response and accurate DC voltage output in eitherAhA嘉泰姆
PFM or PWM Mode. In Pulse Frequency Mode (PFM), the CXSD6293 pro-AhA嘉泰姆
vides very high efficiency over light to heavy loads with loading-modulatedAhA嘉泰姆
switching frequencies. The device works in ultrasonic mode with PFM at noAhA嘉泰姆
load. The unique ultrasonic mode maintains the switching frequency aboveAhA嘉泰姆
20kHz, which eliminates noise in audio applications.AhA嘉泰姆
          The CXSD6293 is equipped with accurate over-current,outputAhA嘉泰姆
under-voltage, and output over-voltage protections.A Power-On-ResetAhA嘉泰姆
function monitors the voltage on VCC to prevent wrong operation duringAhA嘉泰姆
power-on. The CXSD6293 has a 1.5ms digital soft-start to ramp up theAhA嘉泰姆
output voltage to reduce the start-up current. A soft-stop function activelyAhA嘉泰姆
discharges the output capacitors with controlled reverse inductor current.AhA嘉泰姆
The CXSD6293 is available in TDFN3x3-10 packageAhA嘉泰姆
二.产品特点(Features)AhA嘉泰姆

1.)Operates from An Input Battery Voltage Range of +3V to +25VAhA嘉泰姆
      ±0.6% 0.5V Reference Over Line, Load Regulation, andAhA嘉泰姆
      Operating Temp. AhA嘉泰姆
2.)Drive Dual Low Cost N-Channel MOSFETsAhA嘉泰姆
    Adaptive Shoot-Through Protection AhA嘉泰姆
3.)Power-On-Reset Monitoring on VCC PinAhA嘉泰姆
4.)PFM Mode for Increasing Light Load EfficiencyAhA嘉泰姆
5.)Constant-On-Time Control SchemeAhA嘉泰姆
     Switching Frequency Compensation for PWM OperationAhA嘉泰姆
6.)300kHz Constant Switching FrequencyAhA嘉泰姆
7.)Integrated MOSFET Drivers and Bootstrap DiodeAhA嘉泰姆
8.)Internal Soft-Start and Soft-StopAhA嘉泰姆
9.)Power Good MonitoringAhA嘉泰姆
10.)70% Under-Voltage ProtectionAhA嘉泰姆
11.)125% Over-Voltage ProtectionAhA嘉泰姆
     Using Low-Side MOSFET’s RDS(ON)AhA嘉泰姆
12.)Over-Temperature ProtectionAhA嘉泰姆
13.)TDFN-10 3mmx3mm PackageAhA嘉泰姆
14.)Lead Free and Green Devices Available (RoHS Compliant)AhA嘉泰姆
三,应用范围 (Applications)AhA嘉泰姆

NotebookAhA嘉泰姆
Low Cost PCAhA嘉泰姆
Wide Input DC/DC RegulatorsAhA嘉泰姆
四.下载产品资料PDF文档 AhA嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！AhA嘉泰姆

 AhA嘉泰姆

五,产品封装图 (Package)AhA嘉泰姆

AhA嘉泰姆
AhA嘉泰姆

六.电路原理图AhA嘉泰姆

AhA嘉泰姆
七,功能概述AhA嘉泰姆

Constant-On-Time PWM Controller with Input Feed-For-wardAhA嘉泰姆
The constant-on-time control architecture is a pseudo-fixed frequency with input voltage feed-forward. This ar-AhA嘉泰姆
chitecture relies on the output filter capacitor’s effective series resistance (ESR) to act as a current-sense resis-AhA嘉泰姆
tor so the output ripple voltage provides the PWM ramp signal. In PFM operation, the high-side switch on-time isAhA嘉泰姆
controlled by the on-time generator is determined solely by a one-shot whose pulse width is inversely propor-AhA嘉泰姆
tional to the input voltage and directly proportional to the output voltage. In PWM operation, the high-side switchAhA嘉泰姆
on-time is determined by a switching frequency control circuit in the on-time generator block.The switchingAhA嘉泰姆
frequency control circuit senses the switch-ing frequency of the high-side switch and keeps regulat-AhA嘉泰姆
ing it at a constant frequency in PWM mode. The design improves the frequency variation and is more outstand-AhA嘉泰姆
ing than a conventional constant-on-time controller, which has large switching frequency variation over inputAhA嘉泰姆

 voltage,output current, and temperature. Both in PFM and PWM,the on-time generator, which senses input AhA嘉泰姆

voltage on PHASE pin, provides very fast on-time response to input line transients.Another one-shot sets a AhA嘉泰姆

minimum off-time (typical:300ns). The on-time one-shot is triggered if the error com-parator is high, theAhA嘉泰姆

 low-side switch current is below the current-limit threshold, and the minimum off-time one-shot has AhA嘉泰姆

timed out. AhA嘉泰姆
Pulse-Frequency Modulation (PFM)AhA嘉泰姆
In PFM mode, an automatic switchover to pulse-frequency modulation (PFM) takes place at light loads. ThisAhA嘉泰姆
switchover is affected by a comparator that truncates the low-side switch on-time at the inductor current zeroAhA嘉泰姆
crossing. This mechanism causes the threshold between PFM and PWM operation to coincide with the boundaryAhA嘉泰姆
between continuous and discontinuous inductor-current operation (also known as the critical conduction point).AhA嘉泰姆
The on-time of PFM is given by:AhA嘉泰姆
Ultrasonic ModeAhA嘉泰姆
The ultrasonic mode activates an unique PFM mode with a minimum switching frequency of 20kHz. The minimumAhA嘉泰姆
frequency 20kHz of ultrasonic mode eliminates audio-frequency interference in light load condition. It will transitAhA嘉泰姆
to unique PFM mode when output loading makes the frequency bigger than ultrasonic frequency.AhA嘉泰姆
In ultrasonic mode, the controller automatically transits to fixed-frequency PWM operation when the load reachesAhA嘉泰姆
the same critical conduction point (ILOAD(PFM to PWM)).When the controller detects that no switching has oc-AhA嘉泰姆
curred within about 40μs (Typical), an ultrasonic pulse will be occurred. The ultrasonic controller turns on theAhA嘉泰姆
low-side MOSFET firstly to reduce the output voltage. After feedback voltage drops below the internal referenceAhA嘉泰姆
voltage, the controller turns off the low-side MOSFET and triggers a constant-on-time. When the constant-on-AhA嘉泰姆

time has expired, the controller turns on the low-side MOSFET again until the inductor current is below the AhA嘉泰姆

zero-cross-ing threshold. The behavior is the same as PFM mode. AhA嘉泰姆
Power-On-Reset (POR)AhA嘉泰姆
A Power-On-Reset (POR) function is designed to prevent wrong logic controls when the VCC voltage is low. TheAhA嘉泰姆
POR function continually monitors the bias supply volt-age on the VCC pin if at least one of the enable pins is setAhA嘉泰姆
high. When the rising VCC voltage reaches the rising POR voltage threshold (4.2V, typical), the POR signal goesAhA嘉泰姆
high and the chip initiates soft-start operations. When this voltage drops lower than 4.0V (typical), the POR dis-AhA嘉泰姆
ables the chip.AhA嘉泰姆

八,相关产品                更多同类产品...... AhA嘉泰姆

 AhA嘉泰姆

 AhA嘉泰姆

 AhA嘉泰姆

◀ 上一篇:CXSD6292单相恒定时间和同步PWM控制器驱动N通道mosfet降低电池的高压低压芯片

返回顶部

下一篇▶:CXSD6294两相PWM控制芯片为高级显卡和主板应用提供了一个精确的电压调节系统功率MOSFET驱动器与控制器

共有条评论 用户名: 密码: 验证码: 匿名发表