• [ 产品资料下载 ]

样品申请

目录atG嘉泰姆

1.产品概述                       2.产品特点atG嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 atG嘉泰姆
5.产品封装图                     6.电路原理图                   atG嘉泰姆
7.功能概述                        8.相关产品atG嘉泰姆

一,产品概述(General Description)        atG嘉泰姆

      The CXSD61038 are high-efficiency, high frequency synchronous step-downatG嘉泰姆
DC-DC regulator ICs capable of delivering up to 1.5A output currents. TheCXSD61038 can operate over a wide input voltage range from 2.3V to 5.5V andatG嘉泰姆
integrate main switch and synchronous switch with very low RDS(ON) to minimizeatG嘉泰姆
the conduction loss.It is ideal for powering portable equipment that runs from aatG嘉泰姆
single cell Lithium-Ion (Li+) battery. The output voltage can be regulated as low asatG嘉泰姆
0.6V. The CXSD61038 can also run at 100% duty cycle for low dropout operation,atG嘉泰姆
extending battery life in portable system.This device offers two operation modes,atG嘉泰姆
PWM control and PFM Mode switchingcontrol, which allows a high efficiency overatG嘉泰姆
the wider range of the load.atG嘉泰姆
      The CXSD61038 is offered in a low profile (1mm)5-pin, thin SOT package, andatG嘉泰姆
is available in an adjustable version.atG嘉泰姆
二.产品特点(Features)atG嘉泰姆

1.)CXSD61038A 1.2A output currentatG嘉泰姆
2.)CXSD61038B 1.5A output currentatG嘉泰姆
3.)High Efficiency: Up to 96%atG嘉泰姆
4.)1.5MHz Constant Frequency OperationatG嘉泰姆
5.)No Schottky Diode RequiredatG嘉泰姆
6.)2.3V to 5.5V Input Voltage RangeatG嘉泰姆
7.) Output Voltage as Low as 0.6VatG嘉泰姆
8.)100% Duty Cycle in DropoutatG嘉泰姆
9.) Low Quiescent Current: 35μAatG嘉泰姆
10.)Slope Compensated Current Mode Control for Excellent LineatG嘉泰姆
      and Load Transient ResponseatG嘉泰姆
11.)Short Circuit ProtectionatG嘉泰姆
12.) Thermal Fault ProtectionatG嘉泰姆
13.) Inrush Current Limit and Soft StartatG嘉泰姆
14.)<1μA Shutdown CurrentatG嘉泰姆
15.) Tiny SOT23-5 PackageatG嘉泰姆
三,应用范围 (Applications)atG嘉泰姆

Cellular and Smart PhonesatG嘉泰姆
Wireless and DSL ModemsatG嘉泰姆
PDAatG嘉泰姆
Digital Still and Video CamerasatG嘉泰姆
MP3 PlayersatG嘉泰姆
四.下载产品资料PDF文档 atG嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！atG嘉泰姆

 atG嘉泰姆

五,产品封装图 (Package)atG嘉泰姆
atG嘉泰姆

六.电路原理图atG嘉泰姆
atG嘉泰姆

七,功能概述atG嘉泰姆

FUNCTIONAL DESCRIPTIONatG嘉泰姆

CXSD61038 is a synchronous buck regulator IC that integrates the PWM/PFM control, topatG嘉泰姆
and bottom switches on the same die to minimize the switching transition loss andatG嘉泰姆
conduction loss. With ultra low RDS(ON) power switches and proprietary PWM control,atG嘉泰姆
this regulator IC can achieve the highest efficiency and the highest switch frequencyatG嘉泰姆
simultaneously to minimize the external inductor and capacitor size, and thusatG嘉泰姆
achieving the minimum solution footprint.The CXSD61038 requires only three externalatG嘉泰姆
power components (Cin, Cout and L). Theadjustable version can be programmedatG嘉泰姆
with external feedback to any voltage,ranging from 0.6V to the input voltage.atG嘉泰姆
At dropout, the converter duty cycle increases to 100% and the output voltageatG嘉泰姆
tracks the input voltage minus the Rdson drop of the high-side MOSFET.atG嘉泰姆
The internal error amplifier and compensation provides excellent transient response, load,atG嘉泰姆
and line regulation. Soft start function prevents input inrush current and outputatG嘉泰姆
overshoot during start up.atG嘉泰姆
Inductor SelectionatG嘉泰姆
For most designs, the CXSD61038 operates with inductors of 1μH to 4.7μH. Low inductanceatG嘉泰姆
values are physically smaller but require faster switching, which results in some efficiency loss.atG嘉泰姆
The inductor value can be derived from the following equation:atG嘉泰姆
L =VIN × ∆I L × f OSC atG嘉泰姆
Where ∆I L is inductor Ripple Current. Large value inductors result in lower ripple current andatG嘉泰姆
small value inductors result in high ripple current. For optimum voltage-positioning loadatG嘉泰姆
transients, choose an inductor with DC series resistance in the 50mΩ to 150mΩ range.atG嘉泰姆
Input Capacitor SelectionatG嘉泰姆
With the maximum load current at 1.5A, the maximum ripple current through input capacitoratG嘉泰姆
is about 0.6Arms. A typical X7R or better grade ceramic capacitor with 6V rating and greateratG嘉泰姆
than 10uF capacitance can handle this ripple current well. To minimize the potential noiseatG嘉泰姆
problem, place this ceramic capacitor really close to the IN andatG嘉泰姆
GND pins. Care should be taken to minimizethe loop area formed by CIN, and IN/GND pins. atG嘉泰姆
Output Capacitor Selection atG嘉泰姆
The output capacitor is required to keep the output voltage ripple small and to ensureatG嘉泰姆
regulation loop stability. The output capacitor must have low impedance at the switchingatG嘉泰姆
frequency. Ceramic capacitors with X5R or X7R dielectrics are recommended due to their lowatG嘉泰姆
ESR and high ripple current ratings. The outputripple VOUT is determined by:atG嘉泰姆
VOUT × (V IN − VOUT )         1  atG嘉泰姆
V IN × f OSC × L       8 × f osc × C3atG嘉泰姆
A 10μF ceramic can satisfy most applications.PC Board Layout Checklist When laying out the printedatG嘉泰姆
circuit board, the following checking should be used to ensure proper operation of the CXSD61038. Check theatG嘉泰姆
following in your layout:atG嘉泰姆
1. The power traces, consisting of the GND trace, the SW trace and the VIN traceshould be kept short,atG嘉泰姆
    direct and wide.atG嘉泰姆
2. Does the (+) plates of Cin connect to Vin as closely as possible? This capacitor provides the AC currentatG嘉泰姆
    to the internal power MOSFETs.atG嘉泰姆
3. Keep the switching node, SW, away from the sensitive VOUT node.atG嘉泰姆
4. Keep the (-) plates of Cin and Cout as close as possibleatG嘉泰姆
八,相关产品               更多同类产品......atG嘉泰姆

◀ 上一篇:CXSD61037同步降压转换器恒定频率电流脉冲宽度调制模式的降压转换器

返回顶部

下一篇▶:CXSD61038A high frequency synchronous step-down DC-DC regulator ICs capable of delivering up to 1.5A output currents single cell Lithium-Ion (Li+) battery

共有条评论 用户名: 密码: 验证码: 匿名发表