目录V3e嘉泰姆

1.产品概述                       2.产品特点V3e嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 V3e嘉泰姆
5.产品封装图                     6.电路原理图                   V3e嘉泰姆
7.功能概述                        8.相关产品V3e嘉泰姆

一,产品概述(General Description)     V3e嘉泰姆

  The CXSD62129 consists of two independent 1.5MHz constant frequency, current mode, and PWM step-down converters. Each converter integrates a main switch with a synchronous rectifier for high efficiency without an external Schottky diode. The CXSD62129 is ideal for powering portable equipment that runs from a single cell Lithium Ion (Li+) battery. Each converter can supply 1A of loadV3e嘉泰姆
current from a 2.7V to 5.5V input voltage. The output volt age can be regulated as low as 0.6V. The CXSD62129 can also run at 100% duty cycle for low dropout applications.V3e嘉泰姆
二.产品特点(Features)V3e嘉泰姆

1A Output Current on Each ChannelV3e嘉泰姆
2.7V to 5.5V Input Voltage RangeV3e嘉泰姆
1.5MHz Constant Frequency OperationV3e嘉泰姆
Low Dropout Operation at 100% Duty CycleV3e嘉泰姆
Synchronous TopologyV3e嘉泰姆
0.6V Low Reference VoltageV3e嘉泰姆
Current Mode OperationV3e嘉泰姆
Over-Temperature ProtectionV3e嘉泰姆
Over-Current ProtectionV3e嘉泰姆
Up to 94% EfficiencyV3e嘉泰姆
Internally CompensatedV3e嘉泰姆
Lead Free and Green Devices AvailableV3e嘉泰姆
(RoHS Compliant)V3e嘉泰姆
三,应用范围 (Applications)V3e嘉泰姆

TV Tuner/BoxV3e嘉泰姆
Portable InstrumentV3e嘉泰姆
四.下载产品资料PDF文档 V3e嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！V3e嘉泰姆

 V3e嘉泰姆

五,产品封装图 (Package)V3e嘉泰姆

V3e嘉泰姆

六.电路原理图V3e嘉泰姆

V3e嘉泰姆

七,功能概述V3e嘉泰姆

Main Control LoopV3e嘉泰姆

The CXSD62129 has dual independent constant frequency,current-mode PWM step-down converters. During nor-V3e嘉泰姆
mal operation, the internal P-channel power MOSFET is turned on each cycle when the oscillator sets an internalV3e嘉泰姆
RS latch and is turned off when an internal comparator (ICMP) resets the latch. The peak inductor current at whichV3e嘉泰姆
ICMP resets the RS latch is controlled by the voltage on the COMP, which is the output of the error amplifierV3e嘉泰姆
(EAMP). An external resistive divider connected between VOUT and ground allows the EAMP to receive an outputV3e嘉泰姆
feedback voltage VFB at FB pin. When the load current increases, it causes a slightly decrease in VFB associatedV3e嘉泰姆
with the 0.6V reference, which in turn causes the COMP voltage to increase until the average inductor currentV3e嘉泰姆
matches the new load current.V3e嘉泰姆
Soft-StartV3e嘉泰姆
Each channel in the CXSD62129 has a built-in soft-start to control the output voltage rise during start-up. During soft-start, an internal ramp, connected to the one of the posi- tive inputs of the error amplifier, raise up to replace the reference voltage (0.6V typical) until the ramp voltage reaches the reference voltage.V3e嘉泰姆
Short Circuit ProtectionV3e嘉泰姆
For each channel, when the output is shortened to the ground, the frequency of the oscillator will be reduced toV3e嘉泰姆
210kHz. This lower frequency allows the inductor current to safely discharge, thereby preventing current runaway.V3e嘉泰姆
The oscillator’s frequency will gradually increase to its designed rate when the feedback voltage on the FB againV3e嘉泰姆
approaches 0.6V.V3e嘉泰姆
Over-Temperature Protection (OTP)V3e嘉泰姆
For each channel, the over-temperature circuit limits the junction temperature of the CXSD62129. When the junction temperature exceeds 150oC, a thermal sensor turns off the power MOSFETs, allowing the channels to cool down.The thermal sensor allows the converter to start a soft- start process and to regulate the output voltage againV3e嘉泰姆
after the junction temperature cools by 40ïC. The OTP is designed with a 40ïC hysteresis to lower the averageV3e嘉泰姆
Junction Temperature (TJ) during continuous thermal overload conditions, increasing the lifetime of the device. V3e嘉泰姆
Enable/ShutdownV3e嘉泰姆
For each channel, driving EN to the ground places the channel in shutdown mode. When in shutdown, the inter-V3e嘉泰姆
nal power MOSFETs are turned off, all internal circuitry shuts down, and the quiescent supply current reduces toV3e嘉泰姆
1μA maximally. V3e嘉泰姆
Automoatic PFM/PWM mode SwitchV3e嘉泰姆
The CXSD62129 is a fixed frequency PWM peak current modulation control step-down converter. At light loads,V3e嘉泰姆
the CXSD62129 will automatically enter in pulse frequency modulation operation to reduce the dominant switchingV3e嘉泰姆
losses. In PFM operation, the inductor current may reach zero or reverse on each pulse. A zero current comparatorV3e嘉泰姆
turns off the N-channel synchronous MOSFET, forcing DCM (Discontinuous Current Mode) operation at lightV3e嘉泰姆
load. These controls get very low quiescent, help to main- tain high efficiency over the complete load range.V3e嘉泰姆

八,相关产品                 更多同类产品.......V3e嘉泰姆

共有条评论 用户名: 密码: 验证码: 匿名发表